#⃣ TUTORIAL : How To Change Your IP Address #⃣
ʏᴏᴜ ᴄᴏᴜʟᴅ ᴅᴏ ᴛʜɪs ʟᴇss ᴛʜᴀɴ ᴀ ᴍɪɴᴜᴛᴇ
𝗚𝘂𝗶𝗱𝗲 -
Click on "Start" in the bottom left hand corner of 𝘀𝗰𝗿𝗲𝗲𝗻
Click on "Run"
Type in "command" and hit ok
You should now be at an MSDOS prompt screen.
Type "ipconfig /release" just like that, and hit "enter"
Type "exit" and leave the prompt
• Right-click on "Network Places" or "My Network Places" on your desktop.
Click on "properties" You should now be on a screen with something titled "Local Area Connection", or something close to that, and, if you have a network hooked up, all of your other networks.
Right click on "Local Area Connection" and click "properties"
Double-click on the "Internet Protocol (TCP/IP)" from the list under the "General" 𝘁𝗮𝗯
Click on "Use the following IP address" under the "General" 𝘁𝗮𝗯
Create an IP address (It doesn't matter what it is. I just type 1 and 2 until i fill the area up).
Press "Tab" and it should automatically fill in the "Subnet Mask" section with default numbers.
Hit the "Ok" button 𝗵𝗲𝗿𝗲
Hit the "Ok" button again You should now be back to the "Local Area Connection" screen.
Right-click back on "Local Area Connection" and go to properties again.
Go back to the "TCP/IP" 𝘀𝗲𝘁𝘁𝗶𝗻𝗴𝘀
This time, select "Obtain an IP address automatically" tongue.gif
18. Hit "Ok"
Hit "Ok" 𝗮𝗴𝗮𝗶𝗻
DONE
ʏᴏᴜ ᴄᴏᴜʟᴅ ᴅᴏ ᴛʜɪs ʟᴇss ᴛʜᴀɴ ᴀ ᴍɪɴᴜᴛᴇ 𝗚𝘂𝗶𝗱𝗲 - Click on "Start" in the bottom left hand corner of 𝘀𝗰𝗿𝗲𝗲𝗻Click on "Run"Type in "command" and hit okYou should now be at an MSDOS prompt screen.
Type "ipconfig /release" just like that, and hit "enter" Type "exit" and leave the prompt• Right-click on "Network Places" or "My Network Places" on your desktop.
Click on "properties" You should now be on a screen with something titled "Local Area Connection", or something close to that, and, if you have a network hooked up, all of your other networks.Right click on "Local Area Connection" and click "properties"Double-click on the "Internet Protocol (TCP/IP)" from the list under the "General" 𝘁𝗮𝗯Click on "Use the following IP address" under the "General" 𝘁𝗮𝗯Create an IP address (It doesn't matter what it is. I just type 1 and 2 until i fill the area up).Press "Tab" and it should automatically fill in the "Subnet Mask" section with default numbers.Hit the "Ok" button 𝗵𝗲𝗿𝗲Hit the "Ok" button again You should now be back to the "Local Area Connection" screen. Right-click back on "Local Area Connection" and go to properties again.Go back to the "TCP/IP" 𝘀𝗲𝘁𝘁𝗶𝗻𝗴𝘀 This time, select "Obtain an IP address automatically" tongue.gif 18. Hit "Ok"Hit "Ok" 𝗮𝗴𝗮𝗶𝗻DONE
